Monogram ZISW420D Dokumentacja

Dimension Express Booklet To access over 14,000 appliance specification sheets, visit: http://www.dexpress.com Prepared On: . M

ZV800SJ/BJ – GE Monogram™ 36" Chimney HoodSpecifi cation Created 8/04130664Dimensions and Specifi cations (in inches)For answers to your Monogram,®

ZV800SJ/BJ – GE Monogram™ 36" Chimney HoodSpecifi cation Created 8/04130664Wall Mount InstallationsThese hoods may be installed onto a wall or bel

ZV800SJ/BJ – GE Monogram™ 36" Chimney HoodSpecifi cation Created 8/04130664Cabinet RequirementsThis hood may be installed beneath a wall-mounted c

INSTALLATION OPTIONSWALL-MOUNTED INSTALLATIONSThis hood may be installed onto a wall and vented to theoutdoors, or it can be installed for recirculati

Installation Preparation4ADVANCE PLANNING• Determine the exact location of the vent hood.• Plan the route for venting exhaust to the outdoors.• Use th

DUCT FITTINGSUse this chart to compute maximumpermissable lengths for duct runsto outdoors.NOTE: Do not exceed maximumpermissable equivalent lengths!M

INSTALLATION BELOW A WALL CABINETOrder a cabinet that is at least 20” high from the bottom frame to the inside top. The cabinet must be at least 12” d

9INSTALL FRAMING FOR HOODSUPPORTIMPORTANT — Framing must be capable ofsupporting 100 lbs.If drywall is present, mark the screw hole locations forthe t

CONNECT ELECTRICALVerify that power is turned off at the source.WARNING: If house wiring is not 2-wirewith a ground wire, a ground must be provided by

14Installation InstructionsDUCTWORK, WIRING LOCATIONS• Determine the exact location of the vent hood.• Locate the template packed with the literature.

For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000.1

19Installation InstructionsCABINET REQUIREMENTSThis hood may be installed beneath a wall-mountedcabinet.• If the cabinet has been installed, it must b

20Installation InstructionsUNDER-CABINET INSTALLATIONINSTALL FRAMING FOR HOODSUPPORTIMPORTANT: Framing must be capable ofsupporting 100 lbs.If drywall

21Installation InstructionsINSTALL SIDE “L” BRACKETS• Install the “L” brackets onto each side of the cutout.The wide flat portion should be on top of

ZE2160SF – GE Monogram®Microwave OvenDimensions (in inches)Note: JX2127SS or JX2130SS kit is required for in-cabinetinstallation.Installation Informat

2CUTOUT DIMENSIONS* Min. depth with receptacle outside cabinet 191⁄2″Min. depth with receptacle inside cabinet 22″Installation InstructionsModels 27″

Dimensions and Installation Information (in inches)Installation Flexibility These ovens may be installed in combination with a Monogram warming drawer

2Installation InstructionsIMPORTANT SAFETY INSTRUCTIONSWARNING: The electricalpower to the oven supply linemust be shut off while lineconnections are

4Cabinet Width 30” (76.2 cm)RecommendedCutout Locationfrom Floor 32 1/2” (82.6 cm)Cutout Depth 23 1/2” (59.7 cm) Min.Cutout Width 28 1/2” (72.4 cm) Mi

5Installation InstructionsCabinet Width 30” (76.2 cm)RecommendedCutoutLocationfrom Floor 12” (30.5 cm)Cutout Depth 23 1/2” (59.7 cm) Min.

6Installation InstructionsCutout for Single Built-In OvenUnder CounterA3MUST SUPPORT 200 LBS.25”(63.5 cm)24”(61 cm)Gas and electrical connections for3

ADVANCE PLANNING • Refer to “Installation Preparation” forinformation on appropriate placement andnecessary clearances when planninginstallation.• Avo

7CabinetryNOTE: Additional clearances between cutoutsmay be required. Check to be sure the ovensupports above the Warming Drawer locationdo not obstru

8NOTE: The middle rail separating the twoopenings may need to be larger than the 2”(5.1 cm) minimum shown. Always refer to theindividual installation

9Installation InstructionsElectrical ConnectionsATTENTION INSTALLERAll electric wall ovens must be hard wired(direct wired) into an approved junctionb

For answers to your Monogram,® GE Profile™ or GE® appliance questions, visit our website at ge.com or call GE Answer Center® service, 800.626.2000.1

BADesign GuideTHE INSTALLATION SPACEWater And Electrical Locations The opening must be prepared with the electrical and the cold water supply located

1/4"1/2"3/4"1"1-1/4"1"3/4" OverlayPanel(Nominal Size)Stainless Steel1/4"1/2"3/4"2"1-1/4"1-

1/4"1/2"3/4"1"1-1/4"1/4"1/2"3/4"1"1-1/4"1-1/2"23-7/8"From Rear of Refrigerator3/4" Ov

Standard Door Handles3/4" Overlay Panel.10" Thick Spacer Panel1/4" Thick Backer PanelCUSTOMIZATION BASICS: Framed Or Overlay Panels, Cu

1/4" FRAMED PANEL DIMENSIONS7If you choose to install framed panels, they must be cut to the dimensions shown. The panels will slideinto the fram

3/4" OVERLAY PANEL DIMENSIONSFor a more custom appearance, overlay panels may be installed on trimmed models. The overlay panel mustbe secured to

DIMENSIONS AND CLEARANCES1. Overall cooktop dimensions:2. Use a 36″ or wider base cabinet.• Cut the opening in the countertop. To ensureaccuracy, it i

DISPENSER MODELS:RAISED OVERLAY PANEL DESIGNWhen a raised panel design is to be used, a custom wide middle rail is required to acceptthe dispenser tri

GROUNDING THE REFRIGERATORIMPORTANT – (Please read carefully)FOR PERSONAL SAFETY, THIS APPLIANCE MUST BE PROPERLY GROUNDED.The power cord of this appl

Installation InstructionsSTEP 1 REMOVE PACKAGINGCAUTION: The refrigerator is much heavier atthe top than at the bottom—be careful when moving.When us

POWER SUPPLY LOCATIONSGas supply:These cooktops are shipped from the factory set for either natural gas or LP gas. Check to be sure you have the corre

Installation Instructions9INSTALL THE COOKTOPA. Remove the screws on the sides of the cooktopburner box. Use those screws to attach the sidemounting b

COOKTOP INSTALLATION WITH A 36″ MONOGRAM DOWNDRAFT VENT,MODEL ZVB36The installation of the downdraft vent with this cooktop requires careful considera

Installation Options13COOKTOP INSTALLATION OVER A MONOGRAM WARMING DRAWER,MODEL ZTD910 OR ZKD910These cooktops may be installed over a 30″or 27″ Warmi

COOKTOP INSTALLATION OVER A 30″ MONOGRAM SINGLE OVEN,MODEL ZET1 OR ZET938These cooktops may be installed over theMonogram ZET1 or ZET938 single oven.